Specialty Tools for Use on Harley-Davidson Motorcycles

 

        2-3 Days Shipping in the US
Free Shipping on orders of $150.00 in the US
International Orders Accepted

            Secure Check Out

06-Pres Twin Cam Engine Tools

Home 84-99 Evo Engine 99-06 T/Cam Engine 06-Up T/Cam Engine Trans/Primary Pre-06 Trans/Primary 06-Up Chassis Tools Shop Tools Harley Clutch Covers by George's Garage Links Privacy/Terms

                                                                                                                   
 

                                                       

320400

320530

OIL PUMP ALIGNMENT SCREWS, PAIR

99-Present Twin Cam Models

Designed to align oil pump to support plate. A must for proper alignment of the gears & oil pressure. Sold as a pair.

PRODUCT IN STOCK

$17.50

320610

CAMSHAFT  ASSEMBLY TOOL

06-Pres Dyna, 07-Pres T/Cam Models

Designed to hold both camshafts in an upright position while lowering the cam support over both guides. Made of non-marring Delron

HD-47956

PRODUCT IN STOCK

$92.50

320620

CAM GEAR LOCKING TOOL

06-Pres Dyna, 07-Pres T/Cam Models

Designed to lock the Cam & Pinion gears to properly remove, install and torque the holding bolts

HD-47941

PRODUCT IN STOCK

$32.50

320640

INNER CAM BEARING PULLER

06-Pres Dyna, 07-Pres T/Cam Models

Designed to pull the inner cam bearings perfectly straight and prevent the needles from falling into the engine case

PRODUCT IN STOCK

$95.50

320650

INNER CAM BEARING INSTALLER

06-Pres Dyna, 07-Pres T/Cam Models

Designed to install the inner cam bearings perfectly straight and to the proper depth

(Cam bearings at bottom of page)

PRODUCT IN STOCK

$82.25

320652

INNER CAM BEARING PILOT

06-Pres Dyna, 07-Pres T/Cam Models

Upgrade your inner cam bearing installer (320550) on previous page for the new model bikes

 

PRODUCT IN STOCK

$39.95

320660

CAM RELIEF PILOT

06-Pres Dyna, 07-Pres T/Cam Models

Use with Cam Relief Tool, single (320580) or dual (320590) spindle on previous page

PRODUCT IN STOCK

$39.95

340050

PUSHROD CLIP INSTALLER

Use on all Models

Used to install the pushrod clip by prying down on the center spring and sliding the clip into place at the same time

PRODUCT IN STOCK

$29.95

910004

INNER CAM BEARINGS

 (Koyo/Torrington B-168)

06-Pres Dyna, 07-Pres Twin Cam Models

The only bearings with a full roller set to protect your motor

PRODUCT IN STOCK

$19.95

320670

CRANKCASE BEARING REMOVER & INSTALLER

03-Pres Alpha & Beta Engines

Use on 03-Pres Alpha Engines, Pinion & Sprocket Side. 03-Pres Beta Engines Sprocket Side

PRODUCT IN STOCK

$108.00

 

 

320680

SPROCKET SHAFT ADAPTOR KIT

06-Pres Dyna, 07-Pres T/Cam Models

Use to install Timken Bearing or Roller Bearing Inner Race. Use with 500040 Sprocket Shaft Bearing installation Tool

PRODUCT IN STOCK

$49.50

340070

EXHAUST STUD DRILL JIG

84-Pres Big Twins, 83-Pres XL, 87-Pres Buell Except 1125R

Use this jig to drill out broken exhaust studs. Drill bushing allows straight alignment for removal. Supplied with drill bit.

PRODUCT IN STOCK

$66.50

TORQUE PLATES

99-Present Twin Cam Models

Use these plates to check cylinder run-out, honing and boring cylinders. A must for engine work. Range 3.750 thru 3.938

PRODUCT IN STOCK

$298.95